起源の: | 中国 |
ブランド名: | Hongce |
証明: | Calibration certificate(cost additional) |
モデル番号: | HH0813D |
最小注文数量: | 1セット |
---|---|
価格: | 谈判 |
パッケージの詳細: | 合板 |
受渡し時間: | 45日 |
支払:: | T/T |
供給の能力: | 1ヶ月あたりの10セット |
製品名: | 塩の喷雾室 | 電源: | 230V 、60Hz |
---|---|---|---|
保証: | 1年 | 標準: | JIS、ASTM、CNS |
适用: | 耐食性のテスト | 内部ののサイズ: | 2000x800x600mm |
スプレー:: | プログラム可能なスプレー | スプレー量: | 1.0〜2.0ml /80cmの² /h |
ハイライト: | jisの塩の室,,,,ASTMの进入试験装置 |
JIS / ASTM / CNS入口保护测试设备盐喷雾室2000x800x600mm
Product Introduction:
盐喷雾测试机用于各种材料的表面处理,包括涂料,电镀,有机和无机涂层,阳极氧化,抗粘液油和其他抗腐蚀处理,以测试其耐腐蚀性,从而确定产品的质量。
Inner chamber introduction:
喷塔 | The built-in glass nozzle is placed inside the spray tube, and the spray is guided through the tower tube and dispersed into the test chamber through the cone disperser. |
Spray regulator | 通过增加或减少喷雾剂来调整喷雾量。盐水预热的水箱位于喷塔的底部。它的盐水从补充瓶中注入到水箱中。水位由浮球球自动控制。排水插座清洁被水箱底部的硅胶软木塞粘住。 |
Collector | 喷出喷嘴的喷雾将以自由秋季的方式落入一个80cm2的V形容器中,并将通过管子导致测量杯。 |
架子 | The rack is made of plastic-steel. The maximum rack load shall be 2kg for single lading point or 10kg for scattered lading points. |
Heating tank | U形加热管配备了一个用于测试室的加热罐,该储物室用于加热水以保持测试室中的温度稳定,其功能是加热和供暖。 |
Metering tube | Collect the spray volume for each test. |
Water-sealed tank: | 5厘米宽的水箱在透明的丙烯酸ic cover is sealed with water to prevent salt spray from leaking. |
饱和空气桶 | It is placed inside the control box, and its function is to heat and humidify the air through this pail, so that the air reaches the saturated humidity and sprays. |
Test inlet | 自动补充盐水预热罐的盐溶液。 |
Chamber cover | 屋顶状的透明顶部,其角度为100º角,覆盖机器并统一机器。 |
Adjust press valve | 该阀用于调节喷雾压力。仅当打开喷雾开关并且机器正常运行时才能进行调整(测试条件1kg /cm²) |
Pressure meter | 它显示了从饱和空气到的空气的压力 nozzle (testing pressure: 1kg/cm2) |
排气管 | The diameter of the exhaust pipe is 48mm. The spray in the chamber is discharged through this hole. When testing, it is best to connect a hose to lead the spray to the outside. Do not block or have water accumulation. |
Chamber drain valve | 红球阀配备了4点PVC水管。当室内水脏且需要更换室水时,该阀将打开。 |
测试室温度控制器 | 根据标准控制腔室的温度,腔室的温度在35℃下受到控制。 |
Saturated-air pail temperature controller | 控制饱和空气桶的温度,另一个安全保护装置,温度安全集值比实际温度高5°C。(位于控制盒中) |
Timer | Set testing time from 0.1s to 9999hr and stop the machine when the time expires. |
Salt water spray test | 35℃用于测试室控制器,饱和空气桶控制器的47℃(40℃-50℃)。 |
耐腐蚀测试 | 50℃用于测试室控制器,饱和空气桶控制器的65℃(60℃-70℃)。 |
Power switch | 照明的摇杆开关。控制整个机器的电源。 |
Operation switch | 照明的摇杆开关。控制饱和空气桶的加热器系统。 |
计时器开关 | 照明的摇杆开关。Control the power of timer. |
喷开开关 | 照明的摇杆开关。Control the spray system. |
Defogger开关 | Illuminated rocker switch type. Control the defogger system and get rid of the salt spray inside the box. |
室内水短灯 | 当腔室中的水位低于极限时,将打开光线,并将停止操作。 |
Pressure water shortage lamp | The light will be turned on and the operation will be stopped when the water level in the saturated-air pail is lower than the limit. |
缺少盐水 | 当盐水预热储罐的水位低于极限时,将打开光线,并将停止操作。 |
Product front view A: Product back view B:
A: | B: |
1.Test chamber | 8.Compressed air inlet |
2. Manual water filling place for pressure pail | 9.Exhaust |
3.Metering tube | 10.电源230V |
4.Brine inlet | 11.Chamber drainage valve |
5.控制平面 | 12.覆盖支持框架 |
6.调整新闻阀 | |
7.Control box door |
Technical Parameters:
Model | HH0813D |
Inner chamber size (mm) | 2000x800x600mm(w*d*h) |
外室尺寸(mm) | 2300x1100x1400mm(w*d*h) |
测试室温度 | 盐水测试方法(NSS ACSS AASS)35±1±1℃/腐蚀性测试方法(CASS)50℃±1℃ |
压力桶温度 | 盐水测试方法(NSS ACSS AASS)47±1±1℃/腐蚀性测试方法(CASS)63±1℃ |
Salt concentration | 氯化钠的浓度为5%或5%的氯化钠浓度添加0.26克每升氯化铜(CUCL2 2H2O) |
Compressed air pressure | 1.00±0.01kgf/cm² |
喷雾量 | 1.0〜2.0ml/80cm²/h(至少收集16小时,以平均值为单位) |
Relative humidity of testing chamber | 超过85% |
Acid value PH | 6.5〜7.2 3.0〜3.2 |
喷雾模式 | Programmable spray (including continuous spray and intermittent spray) |
满足标准 | JIS,ASTM,CNS |
Power supply | 230V, 60Hz |
图片视图:
コンタクト::sales
電話番号:+8618826455520